LGB 28001 PDF

LGB Gesuperde postwagon,verlichting & metalen wielen LGB Post Container-Tragwagen RhB % . LGB DR-Dampflok 99 View and Download LGB instruction manual online. Toy pdf manual download. USA GB DR RĂ¼gen Steam Locomotive, THE. I have just acquired an LGB which is DCC ready but not fitted. I want to fit a Massoth LS sound decoder but I can’t get into the beast.

Author: Mukazahn Nera
Country: Philippines
Language: English (Spanish)
Genre: Photos
Published (Last): 28 September 2007
Pages: 290
PDF File Size: 15.74 Mb
ePub File Size: 17.69 Mb
ISBN: 771-6-85713-141-2
Downloads: 5952
Price: Free* [*Free Regsitration Required]
Uploader: Brakree

The Champex-linden site shows the exploded components for the loco including screws. Separating the boiler and cab was not too bad. TBH I don’t remember, however the instruction and service diagram can be found here: You have to do it gently as the wires for the cab and rear lights and 4-way switch are not very long. Now the combined cab and boiler should lift off.

I have finished the decoder install so I have done a write-up. This may help you identify what is holding things together. Calendar Monthly Weekly Agenda Archive. It then slides out towards the cab end. Media New media New comments Search media. Everywhere Threads This forum This thread. There will still 288001 some wiring connecting them which is the 4 lbg harness connecting the circuit board to the motor block. Remove the boiler front 17 and unplug the front lights and smoke generator wiring.

I think Zerogee has done this as he said how difficult it was in a post in ! I really need someone who’s done this before to advise. I hope the screw is not under the motor block as pgb looks like a pig to remove.


LGB Instruction Manual (Page 7 of 14)

I have removed the main screws from the base and lbg body shell almost comes off but there seems to be something in the middle of the boiler preventing it, I assume some hidden screw. Facebook Pinterest Email Link. Search Everywhere Threads This forum This thread. Forums New posts Trending Search forums. To install a decoder, you have to disassemble the loco. Unplug either end of that cable and you should be able to separate the cab and boiler from the chassis.

For future reference, from the exploded parts diagram you have to undo screws K, LM, N, O, P, Q, R on page 3 and then gently prise llgb parts 51 and 52 from page 2 to release the valve gear. Thanks in advance, Dave. For a better experience, please enable JavaScript in your browser before proceeding. I used the exploded parts diagram referenced in an earlier posting as a guide. Even though the is not a sound equipped loco they allow for the upgrade as the firebox frontage unclips to reveal a 57mm speaker enclosure and grill, and the smaller dome has provision for an external volume control, both of which will be very handy.

By continuing to use this site, you are consenting to our use of cookies. As you said in your posting it is easier if you remove all the pipes, valves and other gubbins first, then it is lgn question of gentle brute force, there are no screws involved. The weight in the boiler is held in by 3 screws under the boiler.

Opening LGB 28001 Rugen 0-8-0T

The analog circuit board is attached to the weight by another 3 screws. I want to fit a Massoth LS sound decoder but I can’t get into the beast. The page numbers listed below reference that document. Beware that the cab weight may fall out at this point! There are some screws marked on page 3 of the exploded parts diagram which seem to be the culprit but to get to those I would have to remove the motor block which I have already tried but stopped as it looked to be far too complicated.


I will keep that board so I need to work out which wire does what, but no need for the 4 way switch. If I’ve done it right this is the link https: Not too hard when you know that secret. If I ever have to get back inside it again, or do anotheryour notes will be a great help! Before it will come off completely you have to unplug the 8 wires behind the smokebox door 3 front lights and smoke generator and ease out the 4 wire plug on top of the motor block.

That is connected to the main board by a black 5 wire plug. Thanks guys I should have said I already have both of those documents but they are not helping.

Can someone who has done this before let me know the secret or point me at some dismantling instructions?