DIN 8593-5 PDF

Standards. DIN Manufacturing processes joining – Part 5: Joining by forming processes; Classification, subdivision, terms and definitions. Title ( German). DIN references following documents: DIN , , Manufacturing processes joining – Part 5: Joining by forming processes; Classification. Find the most up-to-date version of DIN at Engineering

Author: Nigar Yozshule
Country: Cyprus
Language: English (Spanish)
Genre: Marketing
Published (Last): 12 May 2017
Pages: 306
PDF File Size: 7.18 Mb
ePub File Size: 11.65 Mb
ISBN: 832-9-63022-703-8
Downloads: 75020
Price: Free* [*Free Regsitration Required]
Uploader: Jujas

The article presents the analysis of the structure of the load capacity of riveted joints. With segmented dies, the microsections must be located in the center of the die segments.

Introduction Joining by upset bulging is a mechanical joining process, which is commonly used to create joints with a form and force fit between tubes and other structures, such as 8593–5, plates, tubes, or profiles. J Mater Process Technol 9: If this is not the case, the joint is NOK.

This service is more advanced with JavaScript available, learn more at http: If the material flow in the structure is uninterrupted, as can be seen in the Figure on the 85593-5, it is a wrinkle. This is a preview of subscription content, log in to check access. Joining by Upset Bulging.

The result Fmin Ftransverse — 2 sigma is a reference value for the drawing specification. An axial compression load is usually applied to a rotation-symmetric workpiece e. J Mater Process Technol 5: Page 17 VW Especially for round joints, care must be taken that the joint does not fall apart when preparing the microsections.

  COMPANIESHOUSE GOV UK INFOANDGUIDE FAQ WEBFILINGUSERGUIDE PDF

It is also possible to join surfacetreated parts zinc-coated, aluminized, organically coated, etc.

Nahtlose kaltgezogene Rohre; [Precision steel tubes — technical delivery conditions — part 1: J Clean Prod 19 6—7: Rectangular joints are to be located perpendicular to the load 5893-5. Metallic continuity may occur under certain conditions. In this Section terminological inconsistencies may occur as the original titles are used.

Joining by Upset Bulging | SpringerLink

Sign in to annotate. Undercut f not present on both sides: De Gruyter – Sciendo. Beuth, Berlin Google Scholar. The English translation is believed to be accurate. Such processes are necessary to fulfill the growing demands on industrial production of multi-material joints and general lightweight production. The assessment criteria according to Section 3.

VW _2_TOX铆接_图文_百度文库

These bulges are used to clamp a joining partner e. From all sheets and rivet specimens arrangements the highest load capacity of the joint was obtained for the DC01 sheet material joints, and the lowest load capacity of the joint was obtained for the EN AW sheet material joints.

It is the joining of at least two overlapping sheet metal, tube or profile parts achieved by means of cold deformation with punch and die. Joining by forming processes; Classification, subdivision, terms and definitions Clinchen -?

If the base is cracked, check for microsection preparation errors. The connection is a positive locking and friction locking joint. In the latter case, the microsection must be prepared so that the microsection plane is located in the center of the clinched joint for the determination of the geometric characteristics.

  EN LA MASMEDULA GIRONDO PDF

The Structure of the Strength of Riveted Joints Determined in the Lap Joint Tensile Shear Test

There are no generally applicable values for the base thickness tb. Page 13 VW Living reference work entry First Online: Release testing process qualification A total of 10 specimens according to Section 3. Here, it must be ensured that the measured values are not affected by the preparation work. The minimum break force Fmin depends on the sheet thickness combination, the strength of the raw material and the type of joint and must be specified in the drawing.

Joining by Upset Bulging

Their properties must match to the cases to be tested. J Manuf Process 15 1: For details on the assessment of round clinched joints without cutting element, see PV No part of this document may be transmitted or reproduced without prior permission of a Standards Department of the Volkswagen Group.

For sheets with different plasticity characteristics, the harder sheet is to be arranged on the side of the punch wherever possible “hard in soft”. General information — — Part no. The overall thickness of the joining partners must not exceed 5 mm.