ASTM D5261 PDF

D Mirafi N Geotextile Fabric. KEVIN YAMAKAWA/BA. JUNE 21, ATTACHMENT. SHEET 1 OF 5. ASTM D Standard Test Method. ASTM D Standard Test Method for Measuring Mass per Unit Area of Geotextiles. This standard is issued under the fixed designation D ; the number immediately This test method is under the jurisdiction of ASTM Committee D35 on.

Author: Kemuro Mule
Country: Burkina Faso
Language: English (Spanish)
Genre: Health and Food
Published (Last): 4 July 2018
Pages: 468
PDF File Size: 9.33 Mb
ePub File Size: 1.54 Mb
ISBN: 220-4-64281-843-5
Downloads: 40752
Price: Free* [*Free Regsitration Required]
Uploader: Mikasar

If the document is revised or amended, you will be notified by email. Remember me Forgot d55261 If a bias is found, fou nd, eit either her its cau cause se mus mustt be fou found nd and correcte corrected d or the purchaser and the manufacturer must agree to interpret future test results in light of the known bias.

Proceed to Checkout Continue Shopping. As the voice of the U. Link to Active This link will always route to the current Active version of the standard. Competent statistical assistance is recommended for the investigation of bias.

A superscript supersc ript epsilon e indicates an editorial change since the last revision or reapproval.

ASTM D – 10() Standard Test Method for Measuring Mass per Unit Area of Geotextiles

Your consent to our cookies if you continue to use this website. Equilibrium is considered to have been reached when the increase in mass of the test specimen asstm successive weighings, made at intervals of not less than 2 h, does not exceed If a bias is found, either its cause must be found and corrected or the purchaser and the manufacturer must agree to interpret future test results in light of the known bias.

  COURS FROID INDUSTRIEL OFPPT PDF

The test specimen should then be randomly assigned in equal numbers to each laboratory for testing.

Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Please first log in with a verified email before subscribing to alerts. Precision and Bias The test specimen should then be randomly assigned in equal numbers to each laboratory for testing.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Current edition approved June 15, This standard is not included in any packages.

A time of at least 24 h has been found acceptable in most cases. Add to Alert PDF. Already Subscribed to this document.

Each test specimen shall be equal in area not less than 10 mm2 It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

This test method can be used for aatm control to determine specimen conformance.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and f5261 the applicability of regulatory limitations prior to use. While such a procedure cannot be accepted in cases of dispute, The values stated in parentheses are provided for information only. We have no amendments or corrections for this standard. For the laboratory sample, take a full width swatch of sufficient length along the salvage so that the requirements of 7.

  HAZEL COMPLEMENTOS MUJER FILETYPE PDF

Sco Scope pe 3.

As a minimum, the two parties should take a group of test specimens that sstm as homogeneous as possible and which are from a lot of material of the type in question.

This measurement allows for a simple control of the delivered material by a comparison of the mass per unit area of the delivered material and the specified mass per unit area.

ASTM D astmimportantespara la destilacion a presiones inferiores de 1 atm, archivo actualizadoen la ultima version. As asm minimum, the two parties should take a group of test specimens that are as homogeneous as possible and which are from a lot of material of the type in question.

Astm d5261

SITE To ensure the functioning of the site, we use cookies. Field experience has shown that a test specimen with an area not less than 90 mm2 Need more than one copy? A number in parentheses indicates the year of last reapproval.