Again, we appreciate your selection of an Airtronics Radio Control System and wish you many hours of flying enjoyment. RD Transmitter Specifications. AIRTRONICS. RD Radio System. Operating Manual. INTIMES no! Airplane Thank you for selecting the Airtronic RD Radio System. In deigning the. download airtronics rd manual. I need a owners manual for an Airtronics RD radio (not the super).. I found one here, but it’s $

Author: Mazull Yogar
Country: Japan
Language: English (Spanish)
Genre: Art
Published (Last): 4 August 2014
Pages: 336
PDF File Size: 14.25 Mb
ePub File Size: 12.66 Mb
ISBN: 582-1-44049-495-2
Downloads: 51734
Price: Free* [*Free Regsitration Required]
Uploader: Gardazilkree

Now both ailerons respond identically to the CROW command. Differential refers to the ratio of up-to-down movement of each aileron. Before turning off any unused feature screens, make sure they are at there default setting or do not have any affect on any control surface. Page of 75 Go. The Spoiron function is normally used with sailplanes.

If you deside you later that you want to use a feature you have turned off, you can at anytime use the OPT to turn the feature back on.

Reinstall the transmitter rear case and be careful when placing over ther NiCd battery connector pins. It is best to leave at least mxnual threads inside Part A when screwed out to its longest length for the best mechanical security. You should set the packaging aside for use if you ever need to send your radio in for service, or to store your This screen allows you to move up and down as well as left and right on the screen in the RD Super program.

At this point Model 3 data is still intact, so if you wish to change the destination for the copied data, do so before proceeding. The 600 reversal function is not selective. Activate the Landing Gear toggle switch located on the upper left top of the transmitter when setting the values for the Landing Gear.



For instance, if you have your aircraft program in Model 1 and nothing in Model 3, you can copy the Model 1 program into Model 3 with the copy function. This equipment has been tested in accordance with the requirements contained in the appropriate Commission regulations. You must always be aware of which flight mode you have selected before starting your engine airttronics attempting flight!

In addition, there are bar graph indicators on the screen at all times that visually show how much trim has been set for Elevator, Aileron, Throttle and Rudder channels. These are in addition to the predefined mixers.

The amount of CROW that is used should be adjusted to suit personal preference. The RD Super is packed with all of the capabilities that the beginner as well as the more advanced modelers demand for all three types of flying. You can set the value for the Elevator channel Exponential.

For Sale – Airtronics RD Super, 2 receivers – RC Groups

Each type of aircraft, i. When the Bar Graph reads less than half you should not fly until you recharge the transmitter.

Because of the many features of the RD Super, this manual is quite long. As you bring the stick down and deploy your flaps, the aileron manula differential increases to the amount that you programmed. A new, unread, unused book in perfect condition with no missing or damaged pages. For initial test flights of your model it is recommended that it be set at a value of 7 to allow for maximum ability to trim your model.


Press the Flight Mode switch to select amnual different Flight Modes. B-F-S Battery Fail Safe Will bring the throttle servo to idle when the airborne battery reaches a predetermaned aairtronics voltage.

This allows you to hook up your control linkages and pushrods in the most mechanically desirable manner without regard to the direction of servo movement. Always make sure that you are aware of the present status of any rate assignments that you have selected! Then, switch to another flight mode, and do the same as desired. However, if you want to stop the engine at the end of the flight you would have to use the throttle digital trim and later re-trim for proper idle.

The inital screen will show AR1 which indicates the aircraft type as well as showing the NiCd battery voltage. It can be used with a separete flap servo with an output on the receivers channel 6 or as flaperons with two aileron servos on channel 2 and 6.

Having selected both the data source Model 1 and the desired destination in this example Model 3you can now proceed to confirm the copy function.

Flight Modes are used to allow activation of the DTM function. Reverse the procedure to install a new pack.

Now screw Part A in or out to the desired position and lock it in place by screwing Part B against it. Then scroll down to the TH Fail Safe screen.